Pairing your probe
Pairing links a physical DeFelsko Bluetooth probe to your business inside Autoentic. The first time a probe is paired, there is one extra step, a one-time email check. After that the probe connects straight away on any tablet or phone running the app. Each tablet or phone also signs in once for your business before it starts a new car. This page walks a technician through both, and covers what most often goes wrong.
Before you start
- A tablet or phone with Bluetooth on and the Autoentic app installed. Getting the app explains how to install it.
- A PosiTector Advanced gage with a PosiTector 6000 FN probe or a PosiTector Advanced gage with a PosiTector 200 B probe. It needs the latest DeFelsko update, and it should be on and within a few feet of the tablet.
- An approved email address, the one your business used on the Request Access form. The app sends the code for the first pairing there, and you can't finish the first pairing without it.
Pair inside the app, not from Bluetooth settings
The Autoentic app runs its own Bluetooth handshake. Pairing from the tablet's Bluetooth settings does not register the probe to your business, and the app will still treat the probe as unregistered. Close the settings, open the Autoentic app, and pair there.
Pairing a probe for the first time
-
Open the Autoentic app. It opens on the screen where you connect a probe.
-
Scan, then tap your probe. Tap Scan for Probe. The app lists the probes it finds nearby. Tap yours. If the probe is already registered to your business, you go straight to the app's main screen, with the INSPECT card. If it isn't, the app shows Device Not Registered and asks for your email.
-
Enter your approved email, then the 6-digit code. Type the approved email address and tap Send Code. The app shows Enter Verification Code. Find the 6-digit code in your inbox, enter it and tap Verify. The app then registers the probe to your business.
-
Land on the main screen. The app confirms that the probe is paired and shows the main screen. You're ready to run an inspection.
Checking that the probe is registered
After a successful first pair, sign in to autoentic.com/partner/devices in a browser. Your new probe appears as a row in the table. The row shows its serial number, its model, such as PosiTector, the email that registered it, and the date.
From then on, a technician who connects a probe registered to your business goes straight to the main screen, with no email check. It does not matter which tablet did the pairing, so a probe registered on one tablet is recognized on any of them.
You can pair more than one probe. Each new probe goes through the same steps. Offline the rules are tighter, and Troubleshooting below covers that case.
Signing in each tablet or phone
Each tablet or phone signs in once for your business before it starts a new car. Registering a new probe can sign it in at the same time. If it doesn't, the INSPECT card is greyed out and the main screen shows Sign in under the cards.
To get a code, someone at your business signs in to autoentic.com, opens Phones and tablets and chooses Add a phone or tablet. On the tablet or phone, tap Sign in, type the code under Code and tap Sign in again. It stays signed in when the tablet or phone restarts or the app updates.
To end a sign-in, tap Sign out this device in the app's Settings, or choose Switch off beside the device under Phones and tablets on autoentic.com. The tablet or phone then needs a new code before it starts another car.
The newest version of the app asks for this sign-in. A tablet or phone still on an older version connects without it, and the inspections it sends don't carry your business's name. Inspections from a signed-in tablet or phone carry it once Autoentic has confirmed your business. Autoentic Certified needs the record to name the business that measured it.
Troubleshooting
Power-cycle the probe. Confirm Bluetooth is on at the tablet. Move the probe closer to the tablet and tap Scan for Probe again. Check that the probe is on an Advanced body and that Bluetooth is turned on in the gage's settings. A Standard body has no Bluetooth and never shows up.
Install the latest DeFelsko update on the gage, then pair again.
The email you typed doesn't match an approved business. Check the spelling. If you've requested access, wait for the approval email: the verification code can't be sent before your business is approved.
Check the spam folder. To get another code, tap Send again. If the app asks you to wait first, try again when it lets you. If you typed the wrong email, tap Use a different email and type the approved one.
Close the app, reopen it, and scan again.
Offline, the tablet connects only the probe it paired most recently. For any other probe, get back on Wi-Fi and try again.
Reconnect to Wi-Fi and try again. As long as the app stays open, the tablet still holds the probe you selected. You pick up where you left off, rather than restart the scan. If the app closes before you reconnect, the pairing starts over from the scan and you will need a fresh code.
Next steps
Your probe is paired. Go to Running an inspection for the end-to-end measurement flow.